Low and Slow – how to operate a heat pump efficiently

When you buy a car, the dealer doesn’t teach you how to drive it.  Unfortunately, the same is often true when you buy a heat pump. 

Some installers provide useful tips about how to operate your heat pump – but many don’t see that as part of their job.  Which means that some people with heat pumps end up with higher electricity bills than they should.

Heat pumps are extremely efficient at producing heat – in fact, they are around 300% efficient. They produce around three times as much heat energy as they use in electrical energy, because they extract some heat from the air (or ground).  Whereas a gas or oil boiler is only around 90% efficient.

So a heat pump uses around one quarter of the energy used by a gas or oil boiler.  At the moment, standard tariff electricity is around four times as expensive as natural gas.  Which means that the cost and efficiency balance out, with the result that a heat pump can cost around the same to run as a boiler.

But there are two ways in which this can be changed, to make a heat pump cost less to run than a boiler:

Heat pumps have a lower flow temperature than a gas or oil boiler – the water in the radiators is 50°C or less, whereas a boiler heats the radiators to 70° – 80°C.  Heat pump installers make sure that the radiators in each room are large enough to compensate for this drop in flow temperature, so that they provide the same total amount of heat.

Heat pumps work most efficiently when they are on continuously.  If they are switched on and off a lot, they use more electricity.  Heat pumps are also more efficient if they are set to a low flow temperature, as the hotter the water in the radiators, the more electricity they use.

Hence ‘low and slow’ – to get the best performance from a heat pump, and use the least amount of electricity, it’s best to keep it on for long periods of time and to set the flow temperature at the minimum level needed to keep your home warm.

The most efficient way to do this is to use weather compensation.  This means that the heat pump varies the flow temperature in the radiators according to the temperature outdoors.  So when it is cold outside, the radiators are warmer, and when it is mild outdoors, the radiators are cooler.

The internal thermostat is then used only as an on/off switch – when the heating is on, it is set to a much higher temperature than is needed.  This stops on/off cycling of the heat pump, as conventionally, thermostats turn off the heating system when the target internal temperature is reached.

Now for the technical bit…

The internal temperature of the house is instead controlled by the weather compensation settings.  The upper and lower parameters (levels) for these settings need to be found and set by experimentation, as every home is different.  The maximum flow temperature is set for the coldest weather (say -2°C) and the minimum flow temperature is set for mild weather (around 15°C).  The heat pump then automatically sets all the temperatures in between those settings, by creating something called a heat curve.

To find out what these upper and lower flow temperatures should be, you need a period of cold weather and of mild weather.  When the outdoor temperature is consistently around or below freezing, set a flow temperature of, say, 45°C.  Run the heat pump at this setting for a few days (with any thermostatic radiator valves set to maximum) and monitor the indoor temperature.  If the house is too warm, reduce the flow temperature by a few degrees, until you find the lowest flow temperature that gives you the house temperature that you feel comfortable in. If your home has underfloor heating, the flow temperatures will usually be lower.

Carry out the same procedure when it’s mild outdoors – starting with a flow temperature of around 30°C and then adjusting that.  For a more detailed explanation of this process, see this article from Heat Geek.

You might also need to adjust some of the radiators so that your heating system is balanced – this article from Heat Geek explains how to do that.

This article from Energy Saving Trust also has some useful tips.

You can read more on our website from local residents who have installed heat pumps.

If you’re wondering whether a heat pump will be right for your home you can book a free advice call with our expert Stu (who also wrote this article).

For more general information about what you could do to make your home more energy efficient, then this article might help.

Find more posts in these categories:
Find more posts with these tags: